AAP Elite S series Especificaciones descargar pdf (Pagina 13)

Page 13

LCD KEYPAD “LOCAL EDIT” PROGRAM MODE

LCD KEYPAD “LOCAL EDIT” PROGRAM MODELCD KEYPAD “LOCAL EDIT” PROGRAM MODE

LCD KEYPAD “LOCAL EDIT” PROGRAM MODE

The LCD “Local Edit” Program Mode allows the programming of the keypad address number, the type of control

panel it is connected to, enable the tamper switch and also to program a customised “System Name” (the name dis-

played during idle mode at the keypad) and Customised “Zone Names” (the text that appears on the keypad when a

zone is unsealed).

ACCESSING LOCAL EDIT MODE

To enter Local Edit Program Mode on an AAP LCD Keypad Press “CONTROL” followed by “BYPASS” and hold for

2 seconds.

To enter Local Edit Program Mode on a CROW LCD Keypad Press “CONTROL” followed by “ARM” and hold for 2

seconds.

NOTE: You must press the “Control” button first and the “Bypass” or “Arm” button must be pressed within 2 seconds

of pressing the Control button. If you make a mistake press the “Enter” button then repeat the process.

The display will now show “Local Mode kb #” where the # equals the keypad address as setup at location P900E

(see “LCD keypad address assignment” below for details).

LOCAL EDIT MODE DIRECT PROGRAM ADDRESSES

There are a number of program addresses available to you at this point. They are;

[PROG]-[1]-[ENTER] to; ZONE#1 TEXT (maximum 16 characters)

[PROG]-[64]-[ENTER] ZONE#64 TEXT

[PROG]-[900]-[ENTER] SET KEYPAD ADDRESS NUMBER FROM 1-8

[PROG]-[901]-[ENTER] ENABLE/DISABLE KEYPAD TAMPER SWITCH

[PROG]-[902]-[ENTER] PANEL TYPE (select one of 7 panel types)

[PROG]-[998]-[ENTER] AREA IDENTIFYING CHARACTER (assigning numbers or letters to Areas)

[PROG]-[999]-[ENTER] PANEL NAME DISPLAY (maximum 16 characters)

CHANGING THE ZONE NAMES (P1E - P64E)

When in “Local Edit Program Mode” and you have entered [PROG]-[1]-[ENTER], the display will look like this;

The Cursor will be underneath the first letter to be edited (in this case the “Z”).

The letters <A..Z> indicate that the letters selected by the numeric buttons (0-9) will be in capitals.

By pressing the “MEMORY (AAP)” or “MEM! (CROW)” button once, the display will change to <a..z> indicating that

the letters selected by the numeric buttons (0-9) will be lower case.

By pressing the “MEMORY (AAP)” or “MEM! (CROW)” button again, the display will change to <ד..ג> indicating that

Hebrew characters can be selected by the numeric buttons (0-9).

You can cycle back to another selection by pressing the “STAY (AAP)” or “" (CROW)” button.

Once you have selected the desired font you can now proceed to change the text for Zone 1.

The table on the following page shows the English Characters that can be selected by each numeric button.

The lower case options are shown in ( ).

There are four different selections per button. By pressing the button once, a character will appear in the display (see

“1st press” column below) . Pressing the same button again will cause the display to change to the next character in

the sequence (see “2nd press” column). After you have pressed the same button four times the next press (5th) will

cause the display to wrap back to the beginning.

Once you have selected the first character, Press the “PANIC# (AAP)” or “BYPASS# (CROW)” button to move the

cursor one position to the right.

Now select the second character and move the cursor to the right repeating the process until all of the text is com-

pleted (Remember that there are a maximum of 16 characters per program address).

Zone 1 <A..Z>

one 1

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series