AAP Elite S series Especificaciones descargar pdf (Pagina 79)

Page 79

Enrolling Radio Detectors -Zones 1-64

P680E 1-64E Enrol Radio Detector Zones 1-64 Page 39

If the zone Group assigned to a zone {P341-P404E} is set to a radio device type that incorporates a tamper

switch, e.g. Type #5 “Crow supervised protocol” at addresses P491-P510E, the panel will only load on the

tamper switch opening alarm transmission. If the radio device type for the assigned group is “0” the panel

will load on any transmission. Also the assigned zone group must be set to radio (option 1 off at P471E-

P490E) for the zone to be able to enter learn mode.

Programming Output Options

P681E-P688E OPTIONS

P681E Output #1 Primary options - Default none 1 = Invert Page 41

P682E Output #2 Primary options - Default none 2 = Flashing

P683E Output #3 Primary options - Default none 3 = Single pulse

P684E Output #4 Primary options - Default none 4 = One Shot (lock-out)

P685E Output #5 Primary options - Default none 5 = DTMF command control

P686E Output #6 Primary options - Default none 6 = Local command control

P687E Output #7 Primary options - Default none 7 = Chime alarm to pulse timer

P688E Output #8 Primary options - Default none 8 = Pulsed 24 Hour alarm

Enrolling Radio Keys

P690E 21-100E Enrol Radio Users 21-100 Page 39

(Radio Pendants can occupy User slots 21-100. If a Pendant is programmed against a User slot, that User

slot is not available as a code User).

Alarms to Output Options

P691E Output #1 Alarm options - Default 1,2,3,6 P691E-P698E OPTIONS Page 41

P692E Output #2 Alarm options - Default 1,2,3,6 1 = Keypad panic to output

P693E Output #3 Alarm options - Default 0 2 = Keypad fire to output

P694E Output #4 Alarm options - Default 0 3 = Keypad medical to output

P695E Output #5 Alarm options - Default 0 4 = Duress Alarm to output

P696E Output #6 Alarm options - Default 0 5 = Keypad tamper to output

P697E Output #7 Alarm options - Default 0 6 = Radio key panic to output

P698E Output #8 Alarm options - Default 0 7 = 24 hour alarms

8 = 24 hour fire alarms

Erasing individual Radio codes by transmitting the code

P700E Erase a Transmitted radio code from All Memory Locations Page 39

When erase mode is started and the panel gets a code from the receiver, if that code exists in memory

and its radio device type is “0” {see P680E}, the code will be erased from memory. If the code found in

memory has a radio device type that incorporates a tamper switch, e.g. Type #5 “Crow supervised

protocol” at addresses P491-P510E, then the panel will only erase on the tamper switch opening alarm

transmission.

Secondary Alarms to Output Options

P701E Output #1 Secondary Alarm options 2 - Default 1,2 P701E-P708E OPTIONS Page 42

P702E Output #2 Secondary Alarm options 2 - Default 1,2 1 = Zone tampers to output

P703E Output #3 Secondary Alarm options 2 - Default 0 2 = Cabinet tamper to output

P704E Output #4 Secondary Alarm options 2 - Default 0 3 = Mains fail to output

P705E Output #5 Secondary Alarm options 2 - Default 0 4 = Battery low to output

P706E Output #6 Secondary Alarm options 2 - Default 0 5 = Phone Line failure

P707E Output #7 Secondary Alarm options 2 - Default 0 6 = Failure to get kiss-off

P708E Output #8 Secondary Alarm options 2 - Default 0 7 = Automatic pulse every 5 sec.

8 = 24 Hour alarm reset pulse

ITA Received Signal Strength (RSSI) for Radio Zones 1-64

P709E 1-64E ITA RSSI for Radio Zones 1-64 (Raised lower received level in this mode) Page 41

Received Signal Strength (RSSI) for Radio Zones 1-64

P710E 1-64E RSSI for Radio Zones 1-64 Page 40

Received Signal Strength (RSSI) for Radio Pendants 21-100

P720E 21-100E RSSI for Radio Pendants 21-100 Page 40

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 79

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series