AAP Elite S series Especificaciones descargar pdf (Pagina 37)

Page 37

Option 2 Disarm area when the time zone starts - this option will automatically disarm area "A" when the time-

zone/s programmed at address P669E starts.

Option 3 Disable stay mode exit delay - If this option is on the exit delay for area "A" becomes “0” when arming

stay mode (the delay will still apply to full arm unless option 4 is also on).

Option 4 Disable arm mode exit delay - If this option is on the exit delay for area "A" becomes “0” when arming

the panel (the delay will still apply to stay mode unless option 3 is also on).

Option 5 Disable stay mode entry delay - If this option is on then all zones are instant in stay mode regardless

of any entry delays programmed to zones (entry delays will still apply to zones in full arm mode unless

option 6 is also on).

Option 6 Disable arm mode entry delay - If this option is on then all zones are instant in full arm mode

regardless of any entry delays programmed to zones (entry delays will still apply to zones in stay mode

unless option 5 is also on).

Option 7 Use special stay mode entry delay - If this option is on then all Area “A” Stay mode zones use the

special Stay Mode entry delay (P985E) in stay mode and the normal delays programmed at addresses

P531E-P550E are ignored. The normal delay will still apply during the normal Armed state.

Option 8 Send alarms and bypasses in stay mode - If this option is on then all alarms and zone bypasses in

Stay mode will be reported via the dialler in Contact ID. If the option is turned off, no alarm or bypasses

will be reported when using Stay Mode. Only zone alarms will be reported if using Domestic/ Voice or

Pager reporting formats. You should also note that if a Stay mode alarm is not kissed off in Domestic/

Voice or Pager mode and the alarm is not disarmed, when the dialler test time comes around, the

unreported zone alarms will report again. If this is not desired you can stop this from happening by

turning off all days for the test time at address P816E.

Note: P772E is the same as above but applies to Area B Time & Delay options

Note: P872E is the same as above but applies to Area C Time & Delay options

Note: P972E is the same as above but applies to Area D Time & Delay options

AREA “A” DIALLER REPORTING OPTIONS - P675E

AREA “B” DIALLER REPORTING OPTIONS - P775E

AREA “C” DIALLER REPORTING OPTIONS - P875E

AREA “D” DIALLER REPORTING OPTIONS - P975E

P675E 1 = Send Arm/Disarm

2 = Send Stay Mode Arm/Disarm

3 = Send Disarm only after activations

4 = Send Stay Disarm only after activations

5 = Send Arm at the end of the exit delay

6 = Send all zone restores when disarmed

7 = Spare

8 = Spare

Option 1 Send Arm/Disarm - If this option is on, the dialler will report Area "A" arms and disarms.

Option 2 Send Stay Mode Arm/Disarm - If this option is on, the dialler will report Area "A" stay mode arms and

disarms.

Option 3 Send Disarm only after activation - If this option is on, the dialler will report an Area A disarm following

an alarm activation. If there is no alarm, there will be no arm or disarm reports. This option is often used

in conjunction with alarm only reporting and stops the normal arm/disarm signals from being sent. If this

option is on it will override the option 1 setting.

Option 4 Send Stay Mode Disarm only after activation - If this option is on, the dialler will report an Area A Stay

Mode disarm following an alarm activation. If there is no alarm, there will be no Stay Mode arm or

disarm reports. This option is often used in conjunction with alarm only reporting and stops the normal

Stay Mode arm/disarm signals from being sent. If this option is on it will override the option 2 setting.

Option 5 Send Arm at the end of the exit delay - If this option is Off, the dialler will report an Arm immediately

the panel is armed. If the option is On, the Arm report is sent at the expiry of the exit delay. If the alarm

is disarmed before the exit delay expires, no Arm or Disarm signals will be sent.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 37

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series