AAP Elite S series Especificaciones descargar pdf (Pagina 57)

Page 57

DEFINE OPTIONS FOR EACH TELEPHONE NUMBER - P843E - P848E

These addresses are used to define various options for each of the six phone numbers.

P843E 1 = Monitor Call Progress

2 = Blind Dial

3 = Use Group Numbers for Contact ID

4 = Send Restores

5 = Send Automatic Test calls

6 = Add Prefix to this Telephone Number

7 = Dial using Long DTMF Tones

8 = Ignore Kiss off in Domestic mode

Option 1 Monitor Call Progress - Monitor call progress means that the dialler monitors the status of the dialling

tone to determine whether the call is valid or not. If the call is not valid, i.e. engaged, the panel will know

and hang up the call and try again.

Option 2 Blind Dial - When the dialler makes a call it looks for dial tone before making the call. If no dial tone is

detected the panel hangs up and attempts another call. The panel will do this 3 times and if dial tone is

still not detected it will make the call anyway. If blind dial is on, the panel skips the dial tone detection

and dials 4 seconds after looping the line (used where non standard or low level dial tone exists).

Option 3 Use Group Numbers for CID - If this option is turned off, the panel will send separate account codes to

report the four separate areas when using Contact ID. If the option is on the panel will use one account

code (Area A) and send the group number to identify the four different areas.

Option 4 Send Restores - If this option is turned on, when an alarm is generated the panel automatically sends a

restore when the alarm condition is reset. If the monitoring company does not want restores they may be

turned off with this option.

Option 5 Send Test call to Monitoring Station - The automatic daily test call to a monitoring station can be

enabled, if required, by turning on this option.

Option 6 Add Pre-fix to this Telephone Number - If this option is turned on, the dialling Prefix at address P830E

will be dialled before the telephone number. This is useful if special digits are required to be dialled

before the telephone number to bypass Toll Bars or other similar restrictions. This also allows a number

to be longer than the 16 characters as the Prefix is also 16 characters long.

Option 7 Dial using Long DTMF Tones - It this option is turned off the panel will dial the telephone number using

75ms DTMF tones, if it is turned on the panel will dial using 100ms DTMF tones.

Option 8 Ignore Kiss off in Domestic Mode - If this option is turned on, the panel will not look for a kiss-off when

reporting domestic mode alarms and will run to the maximum re-tries for the scenario then stop. NOTE:

the event must be reported for auto-kiss-off to work, so “call progress” should be turned off if it is

anticipated that a call could be engaged or unanswered, otherwise it will not get reported and then will

not be kissed off automatically.

Note: P844E through P848E are as above but apply to telephone numbers 2-6

SYSTEM EVENTS SCENARIO MAPPING - P931E - P950E

These addresses are used to map System Events as listed below to one of the four possible reporting scenarios. If a

value of zero (0) is assigned at an address in this block, that event will not be reported by the panel.

P931E Duress alarm mapped to scenario 1-4

P932E Keypad Panic Alarm mapped to scenario 1-4

P933E Keypad Fire Alarm mapped to scenario 1-4

P934E Keypad Medical Alarm mapped to scenario 1-4

P935E Battery low mapped to scenario 1-4

P936E Mains fail mapped to scenario 1-4

P937E Phone line restore mapped to scenario 1-4

P938E Radio PIR battery low mapped to scenario 1-4

P939E Radio-key battery low mapped to scenario 1-4

P940E Keypad tamper mapped to scenario 1-4

P941E Cabinet tamper mapped to scenario 1-4

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 57

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series