AAP Elite S series Especificaciones descargar pdf (Pagina 27)

Page 27

P467E Zone Group #17 Options C Default 1

P468E Zone Group #18 Options C Default 1

P469E Zone Group #19 Options C Default 1

P470E Zone Group #20 Options C Default 1

Option 1 Send Multiple reports via Dialler - A zone with this option turned on will send multiple alarm reports via

the dialler. If this option is off, the zone will only report one alarm per armed cycle. If the option “Send

Restores at disarm only” (option 6 at P675E, P775E, P875E & P975E) is turned on, this option must be

turned off for the function to work properly.

Option 2 Sensorwatch Zone - A zone with this option turned on will be monitored for Inactivity. Every time the

zone is triggered during the disarmed state the Sensorwatch timer for this zone will be reset to zero.

When the area that the zone is assigned to is armed, the Sensorwatch timer is stopped with the current

time saved. On disarming of the area, the Sensorwatch timer for the zone will resume with the value

saved when last armed. If the Sensorwatch time for the zone exceeds the programmed value at address

P930E an alarm will be generated. This option is designed to warn if a zone has not been operated for

sometime (possibly faulty or masked). The timer is normally in hours but can be set to minutes by

turning on option 1 at P742E.

Option 3 Soak Test Zone - A zone with this option turned on will be put into soak-test mode. In soak test mode

the zone cannot cause a normal alarm but any alarms when the system is armed will be recorded in the

event memory. This mode is designed to monitor problem zones without causing an alarm.

Option 4-7 Spare -

Option 8 Use second supervise timer # 2 - If this option is off, a supervised radio device will use the first

supervised timer # 1 (P919E). If the option is turned on, a supervised radio device will use supervise

timer # 2 (P920E). This is useful when detectors with different supervise transmission time periods are

used on the same system.

ZONE GROUP OPTIONS D - INPUT CONGIGURATION

Zone Options D

P471E Zone Group #1 Options D Default 1 1 = Zone is Hardwired

P472E Zone Group #2 Options D Default 1 2 = Zone uses 2k2 EOL resistor

P473E Zone Group #3 Options D Default 1 3 = Zone is monitored for Tamper

P474E Zone Group #4 Options D Default 1 4 = Zone is a Keyswitch

P475E Zone Group #5 Options D Default 1 5 = Keyswitch Arms the Area

P476E Zone Group #6 Options D Default 1 6 = Keyswitch is momentary

P477E Zone Group #7 Options D Default 1 7 = Zone uses NC contact

P478E Zone Group #8 Options D Default 1 8 = Zone is a Vibration detector

P479E Zone Group #9 Options D Default 1

P480E Zone Group #10 Options D Default 1

P481E Zone Group #11 Options D Default 1

P482E Zone Group #12 Options D Default 1

P483E Zone Group #13 Options D Default 1

P484E Zone Group #14 Options D Default 1

P485E Zone Group #15 Options D Default 1

P486E Zone Group #16 Options D Default 1

P487E Zone Group #17 Options D Default 1

P488E Zone Group #18 Options D Default 1

P489E Zone Group #19 Options D Default 1

P490E Zone Group #20 Options D Default 1

Option 1 Zone is Hardwired - If this option is turned on, the zone is hardwired. The panel will be looking for a

signal from an ELITE 32EX expander board. If the option is turned off, the zone is a radio zone. The

panel will be looking for a signal from a radio board. If set to hardwired (option 1 ON) the panel will not

allow radio zone learn mode (P680E) to run as the zone is not set to a radio type.

Option 2 Zone uses 2k2 EOL Resistor - If this option is turned on, the hardwired zone must have a 2k2 resistor

fitted to the zone input to seal the zone (type 2 input configuration on Page 6). If the option is turned off,

the input needs to see a short circuit to 0V to seal the input (type 1 input configuration on Page 6).

Option 3 Zone is Monitored for Tamper - If this option is turned on, the panel requires a 2k2 resistor to seal the

tamper and a 4k7 resistor is used for the zone (types 3 & 4 input configuration on Page 6). If the 2k2

resistor is shorted out or the input goes open circuit, a zone tamper will be generated. If the option is

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series