AAP Elite S series Especificaciones Pagina 39

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 103
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 38
Page 39
PROGRAMMING RADIO ZONES
PROGRAMMING RADIO ZONESPROGRAMMING RADIO ZONES
PROGRAMMING RADIO ZONES
ENROLLING RADIO DETECTORS - P680E 1-64E
This address is where radio PIR's, Reed switches and other wireless detectors are enrolled into the panel and
assigned to zones. For the zone learn function to work the assigned zone group must have option 1 at P471E-
P490E turned off for the zone to be able to learn a radio code.
For example; P680E2E Learn Radio Zone #2
P680E3E Learn Radio Zone #3
P680E64E Learn Radio Zone #64
To load a radio detector whilst in installer program mode, for example Zone 1, press P680E1E. The keypad will
beep at 1 second intervals and the green learn mode LED on the Radio receiver board (RX-16) will flash on & off.
Trigger the detector you wish to enrol at this address (Zone 1). The keypad will stop beeping and the receiver learn
LED will turn off when the detectors unique code has been stored. Repeat this sequence for all of the radio
detectors selecting the address which corresponds to the zone you require (eg P680E2E for zone 2, P680E34E for
zone 34, etc). Remember: for a radio zone to work it MUST have a Zone Group assigned at addresses P341E-
P404E that has the correct detector type set (P491E-P510E) and it must be a radio zone (P471E-P490E option 1
off).
If the Zone Group assigned to the zone is set to a radio device type that incorporates a tamper switch (e.g.
Type #5 “Crow FreeWave protocol” at addresses P491E-P510E), then the panel will only learn the code on
the tamper alarm transmission. If the radio device type for the assigned group is “0” the panel will load on
any transmission.
To delete a single radio code location, repeat the learning process above but while in learn mode press the “Enter”
button with no transmitters operating, and this will remove any radio code from that address.
PROGRAMMING RADIO KEYS
PROGRAMMING RADIO KEYSPROGRAMMING RADIO KEYS
PROGRAMMING RADIO KEYS
ENROLLING RADIO KEYS - P690E 21-100E
We refer to wireless handheld transmitters as "Radio Keys". The panel recognises each button on the transmitter as
a separate user so that different functions can be assigned to individual buttons. If you were loading a four button
radio key, you would actually be enrolling 4 separate radio users.
(Users 21-100 can be programmed as Radio Keys. If a User is programmed as a Radio Key, that User slot is
not available as a Code User).
To load a radio key whilst in installer program mode, for example radio key 21, press P690E21E. The keypad will
beep at 1 second intervals and the green learn mode LED on the Radio receiver board (RX-16) will flash on & off.
Trigger the transmitter you wish to enrol at this address (Radio key 21). The keypad will stop beeping and the
receiver learn LED will turn off when the transmitters unique code has been stored. Repeat this sequence for all of
the radio keys selecting the address which corresponds to the User you require.
For example; P690E22E Radio Key #22
P690E23E Radio Key #23
P690E100E Radio Key #100
To delete a single radio key, repeat the learning process above but while in learn mode press the “Enter” button
with no transmitters operating, and this will remove any radio key code from that address.
ERASING INDIVIDUAL RADIO CODES WHILE TRANSMITTING - P700E
P700E Erase a Transmitted radio code from All Memory Locations
When erase mode is started and the panel gets a code from the receiver, if that code exists in memory and its radio
device type is “0”, the code will be erased from memory. If the code found in memory has a radio device type that
incorporates a tamper switch, e.g. Type #5 “Crow FreeWave protocol”, then the panel will only erase on the tamper
alarm transmission.
Vista de pagina 38
1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 102 103

Comentarios a estos manuales

Sin comentarios