AAP Elite S series Especificaciones descargar pdf (Pagina 45)

Page 45

directly by pressing the memory button. If it is turned on the Memory events can only be accessed after

pressing <MEMORY> then a valid code then <ENTER>.

Option 4 Send Output data to keypad buss - This option allows the output updates to the keypad buss for the

OUTPUTX4 board to be turned on if needed. If the option is On the Output data will be sent to the

keypad buss. It is normally turned off unless needed.

Option 5 Output 1 is a siren Output - Output 1 is normally an open drain high current FET output that switches

to 0V when activated. If this option is turned on Output 1 becomes a siren output designed to drive an 8

ohm horn speaker.

Option 6 Inhibit Arming if “Radio Activity Failure” alarm is active - If this option is off, the panel can be armed

even if no signals have been received from any programmed radio detectors within the preset period

programmed at address P929E. If this option is turned on, and no signals have been received from any

radio detectors for the programmed time set at P929E, the panel cannot be armed until a new

transmission is received. This option should only be used when supervised detectors are being used.

Option 7 Test for RF Interference - If this option is turned on the panel can automatically test the RSSI output of

the receiver to see if there is an excessive amount of RF activity. If there is more than 30 seconds of

received data within any 60 second period, the panel will display an “RF Fault” message and beep the

keypad buzzer if programmed to do so at address P804E. This feature should only be turned on if the

receiver fitted has the RSSI output.

Option 8 Installer Must Reset a System Tamper Alarm - If this option is off, the panel can still be used normally

if a system tamper alarm occurs. If the option is turned on, and a system tamper alarm occurs, the user

can reset the alarm but cannot Arm the system until the alarm is reset by an Installer. For the installer to

reset the “arm inhibit” function, they must enter Installer program mode via client program mode so the

installer direct access to program mode feature should be turned off (P741E Option 3) and the code

used to access client mode must have option 7 on at addresses P221E-P240E.

MISCELLANEOUS PANEL OPTIONS 3 - P743E

P743E 1 = Enable Callback Mode

2-8 = Spare

Option 1 Enable Callback Mode - For Security reasons the PC-Panel connection (upload/download) may require

the use of the Callback feature. This feature stops the panel from allowing an upload or download from a

PC unless the panel called the PC on the Callback number. If this option is turned on, Callback is the

only method of connecting with a PC. For the function to work there must be a Callback number

programmed at one of the telephone number locations and that number must have the Callback option

set (P837E-P842E).

EXPANDER FAIL TIMEOUT - P745E

Each expander connected to the panel sends a regular activity signal to show that it is still on-line. The signal is sent

approximately every 3 seconds. Every time an expander sends an on-line signal the timer at this address is reset. If

the timer expires due to a lack of on-line signals from an expander, a trouble alarm will be generated. This timer is

programmed in seconds and has a range of 16-999 seconds.

EXPANDERS CONNECTED TO THE PANEL - P749E

When you enter in address P749E the panel will tell you which expanders are connected. If number 1 is on it shows

that expander I is connected and working, if number 2 is on it shows that expander 2 is connected and working. If an

expander fails to communicate with the main panel or is temporarily removed for any reason the associated number

will be turned off at this location to indicate that it is currently not on-line. When an expander fails, the main panel will

generate and expander fail alarm and the trouble LED will turn on at the keypad. When the expander is back on-line

again the trouble LED will turn off and an expander restore will be generated. As soon as the expander board is back

on-line, the expander number will appear at this location again and main panel will start the expander fail timer

(P745E) for that expander board again. At power-up, if any hardwired zones are assigned to an expander board the

main panel will expect to get an on-line message from that expander. If it doesn’t get the on-line message an

expander fail will be generated. The fail alarm will be reset as soon as the expander is on-line.

P749E 1 = Expander 1 Active

2 = Expander 2 Active

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 102 103

Comentarios a estos manuales

Sin comentarios

AAP Elite S series Especificaciones Pagina 45

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AAP Elite S series